• Quick and easy application Mixing ratio 1:1 by volume.
• Non-flammable water-based product (zero VOC), odor-free. Suitable for indoor or closed sites.
• Very fast curing.
• Good adhesion to concrete with high mechanical resistance, resistance to abrasion and chemical agents.
• Adhesion even on wet supports, iron, galvanized steel, aluminum, glass and wood.
• Breathable. Highly effective as a water vapor barrier.
• Very easy to clean.

Before applying the product, check that the support is clean and free of traces of oil, grease, silicone, contaminating waxes or soil materials. If repair is needed, apply appropriate repair mortars.
Apply at room temperature between +10 ºC and 40 ºC. The temperature of the support must be between +10 ºC and 40 ºC. The support must be dry and with relative humidity < 75% (admits humidity, not waterlogging).
It is important to control the dew point to prevent condensation from occurring and avoid whitish areas on the coating.
It is necessary to start from a porous concrete support, without grout and free of curing liquids. Minimum compressive strength of concrete: 15 N/mm2. Minimum tensile strength of concrete: 1 N/mm2.
If in doubt, carry out a test before application.
Mix the two components in the recommended proportion of 1 part of component A for every 1 part of component B.
Beat component A well in its container, then add component B and beat with an electric stirrer (300-400 rpm) for a minimum of 2 minutes until obtaining a homogeneous product. If overmixed, occluded air bubbles may appear. Once the two components are mixed, it is ready for use. Application open time
(Pot Life) is 1 hour at 25 ºC and 55% RH.

Apply with a brush, roller or airless spray in thin layers with an approximate consumption of 150 g/m2 in two layers. The final consumption will depend on the porosity and roughness of the support. Product ready to use. Dilution is not recommended.
Repainting will be done once the previous layers are dry, approximately 2-24
hours.

Touch dry 3-5 hours
Pedestrian traffic 24 hours
Light traffic 2 days
Total curing 3 days
Data at ambient temperature of +25 ºC and 55% relative humidity.

It can be mixed with quartz sand with a grain size of 0.2-0.4 mm. Mix with a low-speed agitator and apply with a trowel in non-slip treatments. It is recommended to shake frequently to avoid sedimentation of the sand.
Maintenance and cleaning: To maintain the appearance of the floor after application, all spills must be removed immediately after they have occurred. The floor must be cleaned regularly using rotating brushes, high-pressure cleaners, vacuum cleaners, using neutral detergents and appropriate waxes.
Once the container is opened, we recommend its complete consumption. Once the two components have been mixed, the mixture obtained must be applied, respecting the pot-life.
Stable for 12 months from its manufacturing date, in its original, well-closed and undamaged container. Store in a dry and cool place at temperatures between +5ºC and +25ºC.
Application in closed areas must be carried out ensuring proper ventilation during application and 48 hours after.
Do not exceed the maximum consumption because it may affect its adhesion and durability.
Avoid the formation of puddles of the product.
In applications exposed to U.V. rays. yellowing may occur.
For applications with chemical resistance, consult the technical department.
Incorrect treatment of cracks and singular points can lead to a reduction in the useful life of the pavement. Do not reuse to mix or apply with polyurethane products.
To clean materials and utensils, use FUTURSOLVENT 001 before the product hardens. Once the product has hardened it can only be removed by mechanical means.

• Very useful in all types of construction companies, quick repair contracts, general masonry, community maintenance, repair and restoration of buildings, industrial flooring, etc.
Application as:
• Primer suitable for polyurethane, polyurea, acrylic and epoxy systems.
• Concrete sealing.
• Union bridge between old/new mortars.
• Anti-dust layer in the treatment of concrete floors.
• Protective layer for old metal structures.

Supported media:
• Concrete, iron, galvanized steel, aluminum, glass and wood.
• For other supports we recommend carrying out tests to verify their adhesion.